Configurations

Subrack Accessories - Configurations

25 Item(s)

per page

Grid  List 

Set Descending Direction
  • Card Guide CONN

    For easy screwless snap-on mounting of
    connectors accordance to IEC 60 603/
    DIN 41 612.
    With a provision for a spring to contact
    front panels and for contacting a track
    near the PCB edge.
    This snap-in card guides can als be secured with screws.
  • Card Guide ECONOMY

    for subrack FLEXIBLE Card Guide ECONOMY An inexpensive snap-in card guide that can also be secured to the horizontal rails with self tapping screws.


    Technical data


    Material Lexan 500 Color gray


    Continous temperature – 40 °C up to + 115 °C


    Fire protection class UL 94 V–0

  • Card Guide IEEE

    This card guide is in accordance to specification
    IEEE 1101.10.
    The required coding of the IEEE is integrated in the
    card guide head.
    With provision for the IEEE contact spring for groun
    ding of the alignmentpins of the PCB‘s front panel.
    Also with a provision for contacting a track near the
    PCB edge.
    This snap-in card guides can be secured with screws.
  • Card Guide IEEE with 1/2 HP lateral offset

    This card guide is also in accordance to specification
    IEEE 1101.10.
    For CompactPCI-power supplies and for Plug-in units
    fitted with SMD.
    With provision for the IEEE contact spring for groun
    ding of the alignmentpins of the PCB‘s front panel.
    Also with a provision for contacting a track near the
    PCB edge.
    This card guide is secured with screws.
  • Card Guide UNIVERSAL

    This is an allpurpose card guide with provision for a
    spring to contact front panels.
  • Card Guide VARIO

    This is a length variable card guide constructed from 3
    pieces. The center piece can be cut to any length.
    With a provision for a spring to contact front panels.
    These snap-in end pieces can also be secured with
    screws.
  • Card Guide VIB

    Lattice construction for heavy mechanical loads.
    With a provision for a spring to contact front panels
    and for contacting a track
    near the PCB edge.
    This card guides can be snapped in
    and/or secured with screws.

    Two versions:
    1. With pressed-in nut M 2.5
    for assembly to the horizontal rail with
    oval head screws M 2.5 x 12

    2. Without a nut, but one can be added
    in the existing hexagonal molding.
  • Card Guide with integrated push and pull assist

    Card Guide with integrated push and pull assist
    This special card guide with an integral small lever aids
    in the handling of PCB’s with high pin plug in
    connectors.
    The lever is supported by the walls of a special guide
    chamber when the board is pulled out or pushed in.
    It is suitable for a spring to contact a track near the
    PCB edge.
    This card guides are snapin and can be secured with
    screws.
  • Horizontal Mounting Frame

    20 HP for horizontal mounting of 6 U
    PCB‘s in 3 U subracks.
    The horizontal mounting frame needs
    52 HP in the width.
    For 84 HP subracks are available
    Placed right:
    52 HP for horizontal mounting frame,
    32 HP for 3 UPCB‘s
    Placed left:
    52 HP for horizontal mounting frame,
    1 HP for air and leakage paths,
    31 HP for 3 UPCB‘s.
  • Label Strip

    Self adhesive. For identifiying PCB slots in the subrack. The PCB slot
    number can be read thru the hole in the front panel.
    Note:
    The label strip cannot be read while using the RFI spring P2.
    Material: PC/PEfoil
    Color: yellow/black
  • Labelling Rail 84 HP

    This hinged labelling rail is mounted on the subrack flanges. Normally
    it is placed in front of the front panels. For ejecting a PCB, the rail is
    turned down.
  • Locking Rail 84 HP

    For locking of PCB‘s witout front panels.
    The locking rail is mounted at the horizontal rail in front of the PCB‘s.
    A labeling strip can be insert into a groove.
  • Mounting Rail B tapped M 2.5

    Mounting Rail B tapped M 2.5
    For mounting connectors in accordance to IEC 60 603/
    DIN 41 612.
    For mounting at the rear profile on subracks type alpha
    with insulating strip and insulating bushings.
    For mounting at the rear profile on subracks type delta.
    Material: aluminum
    Finish: blank
  • Partition Wall

    Partition Wall
    For partitioning of a subrack part.
    The partition wall 6 U can also be used as a RFI shiel
    ded subrack divider in 6 U and 2x3 U parts.
  • PCB Locking Device Kit

    Secures PCB’s without front panels. Used for easy
    locking and ejecting of PCB’s

25 Item(s)

per page

Grid  List 

Set Descending Direction